AIA/NAS - Aerospace Industries Association
Popular Standards by SDO A-Z
Popular Standards |
|
NAS 15 | JOINT-UNIVERSAL,MALE |
NAS 1503-1510 | BOLT, 100 DEG FLUSH HEAD HI-TORQUE RECESS, SHORT THREAD ALLOY STEEL, 160,000 PSI |
NAS 1511 | HEAT TREATMENT AND PROCESSING REQUIREMENTS FOR 5% CR ULTRA HIGH STRENGTH ALLOY STEEL (H-11) FASTENERS |
NAS 1512-1513 | NUT ASSEMBLY, SELF-LOCKING, GANG CHANNEL-LOW HEIGHT, C'BORE, MINIATURE |
NAS 1514 | RADIOGRAPHIC STANDARD FOR CLASSIFICATION OF FUSION WELD DISCONTINUITIES |
NAS 1515 | WASHER-PLASTIC AND SYNTHETIC RUBBER |
NAS 1516-1522 | PIN, SWAGE LOCKING, ALUMINUM ALLOY, 100 DEG HEAD (MS 24694), TENSION, PULL-TYPE |
NAS 1523 | PACKING WITH RETAINER |
NAS 1524 | STANDARDIZATION SAVINGS, IDENTIFICATION AND CALCULATION |
NAS 1525-1532 | PIN, SWAGE LOCKING, ALUMINUM ALLOY, PROTRUDING HEAD, TENSION, PULL-TYPE |
NAS 1533 | PIN, 100 DEG CKS HEAD HI-SHEAR RIVET, CLOSE TOLERANCE |
NAS 1534 | PRIMER COATING: LOW VOLATILE ORGANIC COMPOUND, CHEMICAL AND SOLVENT RESISTANT |
NAS 1535-1542 | PIN, SWAGE LOCKING, ALUMINUM ALLOY, 100 DEG HEAD (MS 20426), TENSION, PULL-TYPE |
NAS 1543 | VALVE, SHUTOFF, ELECTRIC MOTOR OPERATED, FUEL AND OIL SYSTEM, GENERAL SPECIFICATION FOR |
NAS 1544 | PLATE, WALL, ELECTRICAL, WEATHERPROOF |
NAS 1545 | COATING: LOW VOLATILE ORGANIC COMPOUND, FOR TOPCOAT APPLICATION |
NAS 1546-1552 | PIN, SWAGE LOCKING, ALUMINUM ALLOY, 100 DEG HEAD (MS 24694), TENSION, STUMP-TYPE |
NAS 1553 | KNOB, HAND, GROUND SUPPORT EQUIPMENT |
NAS 1554 | GROMMET, PTFE-SPLIT |
NAS 1555-1562 | PIN, SWAGE LOCKING, ALUMINUM ALLOY, PROTRUDING HEAD, TENSION, STUMP-TYPE |
NAS 1563 | GAGES, PINS AND COLLAR INSPECTION, SWAGE LOCKING |
NAS 1564 | REDUCER, FLARED TUBE |
NAS 1565 | REDUCER, FLARELESS TUBE |
NAS 1566 | REDUCER ASSEMBLY, FLARELESS TUBE |
NAS 1567 | JUNCTION BOX ASSEMBLY CAST AL ALY, WEATHERPROOF |
NAS 1568 | JUNCTION BOX SHEET METAL, NON-WEATHERPROOF |
NAS 1569 | COVER - JUNCTION BOX |
NAS 1570 | GASKET JUNCTION BOX |
NAS 1571 | SWITCH FITTING BOX SINGLE GANG, WEATHERPROOF |
NAS 1572 | SWITCH FITTING BOX TWO GANG, WEATHERPROOF, SINGLE DEVICE |
NAS 1573 | SWITCH FITTING BOX THREE GANG, WEATHERPROOF, SINGLE DEVICE |
NAS 1574 | SWITCH FITTING BOX ONE, TWO, OR THREE GANG, NON-WEATHERPROOF |
NAS 1575 | SWITCH FITTING BOX, WEATHERPROOF |
NAS 1576 | COVER SWITCH FITTING BOX, NON-WEATHERPROOF |
NAS 1577 | GASKET SWITCH FITTING BOX |
NAS 1578 | BOLT, FLAT PAN HEAD |
NAS 1579 | BOLT, FLAT PAN HEAD FULL THREAD |
NAS 1580 | BOLT, SHEAR, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM AND DOVETAIL SLOT, 95 KSI FSU |
NAS 1581 | BOLT, SHEAR, 100° FLUSH REDUCED HEAD, OFFSET CRUCIFORM – RIBBED AND DOVETAIL SLOT, 95 KSI FSU |
NAS 1582 | BOLT, 100 DEG FLUSH TENSION HEAD FULL THREAD |
AIA AIRCRAFT INDUSTRY | AIRCRAFT INDUSTRY SURVEYS ON CURRENT FLIGHT TEST INSTRUMENTATION PRACTICE AND CURRENT APPLICATION OF AUTOMATIC DATA PROCESSING AIRCRAFT RESEARCH AND TESTING COMMITTE |
AIA CARRIAGE OF HANDICAP | CARRIAGE OF HANDICAPPED PERSONS |
AIA DESIGN MANUAL | DESIGN MANUAL ON AIRCRAFT ELECTRICAL INSTALLATIONS |
AIA HIGH-STRENGTH | HIGH-STRENGTH, HIGH-TEMPERATURE MATERIALS FOR STANDARD PARTS SYMPOSIUM |
AIA NAS SET | COMPLETE HARDCOPY SET OF THE AEROSPACE INDUSTRIES ASSOCIATION AIA NATIONAL AEROSPACE STANDARDS *INCLUDES ALL CURRENT & "INACTIVE FORNEW DESIGN" NAS & METRIC NAS STANDARDS* *12 VOLUME SET ADD ON 12 GLOBAL BINDER 3" WHITE & (1) GLOBAL BINDER 1 " WHITE AT N/C |
AIA NAS SET RENEWAL | RENEWAL OF THE ONE YEAR UPDATE SERVICE FOR PURCHASERS OF THE AIA NAS SET |
AIA NAS SET UPDATE | ONE YEAR UPDATE SERVICE FOR PURCHASERS OF THE AIA NAS SET |
AIA PUB 119 | AEROSPACE INDUSTRIES ASSOCIATION PUBS-119 PUBLICATION DOD LIAISON RECOMMENDATION FOR HAZARDOUS MATERIALS WARNING IN TECHNICAL DATA |
AIA TARC 82-29 | STANDARDS FOR SYMBOLOGY AND GRAPHIC SIGNAGE ABOARD COMMERCIAL AIRCRAFT |
AIA TR 91-1 | AEROSPACE INDUSTRIES ASSOCIATION PUBS-119 PUBLICATION DOD LIAISON RECOMMENDATION FOR HAZARDOUS MATERIALS WARNING IN TECHNICAL DATA |
AIA TR 91-2 | JOINT DEPARTMENT OF DEFENSE/INDUSTRY AD HOC COMMITTEE "REDUCING PROCUREMENT LEAD TIMES" |
AIA TR 92-1 | GUIDE TO SIMPLIFIED GRAPHICS |
AIA TR 93-1 | PARTS, MATERIALS AND PROCESSED (PMP) LOG AND SYSTEMS LEVEL ENGINEERING DOCUMENTS (SLED) LOG |
AIA/AMEC PROJECT 259-15 | ASSEMBLY DRILLING METHODS FOR AEROSPACE MATERIALS |
AIA/NAS LAN LICENSE 1 | AIA/NAS LAN LICENCE 1 USER |
AIA/NAS LAN LICENSE 11-20 | AIA/NAS LAN LICENSE 11-20 USERS |
AIA/NAS LAN LICENSE 2-5 | AIA/NAS LAN LICENSE 2/5 USERS |
AIA/NAS LAN LICENSE 6-10 | AIA/NAS LAN LICENSE 6-10 USERS |
ARTC 101 | EVALUATION OF ALUMINUM ALLOY 7001-T75 **CONTAINS FOLDOUTS AND PHOTOS** |
ARTC 11 | DOUBLE-INTEGRATING GYRO TEST INSTRUCTION |
ARTC 13 | STANDARD ELEVATED TEMPERATURE TESTING PROCEDURES FOR METALIC MATERIALS |
ARTC 30 | SURVEY OF FACILITIES FOR SPACE ENVIRONMENT SIMULATION |
ARTC 32 | PANEL FLUTTER SURVEY AND DESIGN CRITERIA |
ARTC 33 | FASTENER AND JOINT TESTING PROCEDURE, ROOM TEMPERATURE |
ARTC 34 | RECOMMENDED PERFORMANCE AND TEST SPECIFICATION FOR TELEMETRY TRANSMITTERS IN THE 1435 TO 1535 MEGACYCLE AND 2200 TO 2300 MEGACYCLE BANDS |
ARTC 35 | PROGRAM TO STANDARDIZE A METHOD FOR DETERMINING LIQUID OXYGEN COMPATIBILITY |
ARTC 36 | PROPOSED ARTC TARGET SPECIFICATION SEALING COMPOUND: HIGH TEMPERATURE (500 DEGREES F - 650 DEGREES F) RESISTANT FOR INTEGRAL FUEL TANKS AND FUEL CELL CAVITIES) |
ARTC 37 | AIRCRAFT ALIGHTING DYNAMICS |
ARTC 38 | CATALOG OF SIMULATION VACUUM CHAMBERS |
ARTC 39 | DEVELOPMENT OF A CONSTANT BANDWIDTH FM STANDARD |
ARTC 4 | ELECTRICAL TEST PROCEDURES FOR RADOMES AND RADOME MATERIALS |
ARTC 40 | INTEGRATED TELEMETRY STANDARDS |
ARTC 41 | RECOMMENDED SAFETY PRACTICES FOR MANNED SPACE CHAMBERS |
ARTC 42 | RADIOGRAPHIC INSPECTION REQUIREMENTS FOR SOLID PROPELLANT MOTORS |
ARTC AIRCRAFT INDUSTRY | AIRCRAFT INDUSTRY SURVEYS ON CURRENT FLIGHT TEST INSRUMENTATION PRACTICE AND CURRENT APPLICATION OF AUTOMATIC DATA PROCESSING |
ARTC PANEL 61-B TASK I | NEWSLETTER NUMBER 1 ON THE SURVEY AND DISSEMINATION OF THERMOPHYSICAL PROPERTIES INFORMATION |
ARTC PROJECT 1-63 | AEROSPACE RESEARCH AND TESTING COMMITTEE - PRELIMINARY CATALOG OF SPACE SIMULATION CHAMBERS |
ARTC/W-76 | AIRCRAFT FATIQUE HANDBOOK - VOLUME II - DESIGN AND ANALYSIS |
ATC TR 101 | EVALUATION OF ALUMINUM ALLOY 7001-T75 |
ATC TR 102 | RELIABILITY DEMONSTRATION FOR AIRCRAFT GAS TURBINE ENGINES |
ATC TR 103 | STRUCTURAL RELIABILITY - PHASE 1 REPORT |
ATC TR 104 | AIRCRAFT GUST CRITERIA SURVEY |
CONSERVATION HANDBOOK | CONSERVATION HANDBOOK - FOR THE USE OF THE INDUSTRY AND THE MILITARY SERVICES |
DESIGN MANUAL ON AIRCRAFT | DESIGN MANUAL ON AIRCRAFT FIRE PROTECTION FOR RECIPROCATING AND GAS TURBINE ENGINE INSTALLATIONS |
EETC REPORT #1 | INTERIM DICTIONARY OF TERMS AND DEFINITIONS RELATING TO RELIABILITY |
EETC REPORT #10 | RESULTS OF GYRO INDUSTRY SURVEY AND RECOMMENDATIONS FOR PHASE 11 EPC/GYRO PROJECT |
EETC REPORT #12 | PROPOSED VERTICAL GYRO TEST INSTRUCTIONS |
EETC REPORT #13 | PROPOSED DIRECTIONAL GYRO TEST INSTRUCTION |
EETC REPORT #14 | PROPOSED FREE GYRO TEST INSTRUCTIONS |
EETC REPORT #15 | ESSENTIAL PERFORMANCE CRITERIA FOR GYROS IN TYPICAL APPLICATIONS |
EETC REPORT #16 | GUIDE LINES FOR RELIABILITY CONSIDERATIONS FOR AIA/EPC |
EETC REPORT #17 | RELIABILITY CONSIDERATIONS IN DESIGN REVIEWS |
EETC REPORT #18 | RELIABILITY AND RELATED DEFINITIONS |
EETC REPORT #19 | RELIABILITY EDUCATIONAL MATERIAL EXCHANGE |
EETC REPORT #20 | RELIABILITY PREDICTION TECHNIQUES |
EETC REPORT #21 | A SURVEY OF RELIABILITY ASPECTS OF INCENTIVE CONTRACTS |
EETC REPORT #22 | SURVEY ESTIMATE OF DOLLAR SAVINGS RESULTING FROM THE UNIFORMITY PROGRAM FOR GENERAL SPECIFICATIONS FOR ELECTRONIC EQUIPMENT |
EETC REPORT #23 | A SURVEY ON METHODS OF IMPLEMENTING A FAILURE REPORTING SYSTEM |
EETC REPORT #24 | DIRECTORY OF GOVERNMENT RELIABILITY OFFICES |
EETC REPORT #25 | A SURVEY ON ELEMENTS OF RELIABILITY CONTROL |
EETC REPORT #26 | TEST CODE FOR HIGH POTENTIAL AND INSULATION TESTING |
EETC REPORT #27 | GUIDELINES TO CONTROLLED RELIABILITY RELAY SPECIFICATIONS |
EETC REPORT #28 | RELIABILITY PREDICTION ADJUSTMENT FACTORS |
EETC REPORT #29 | REQUIREMENTS FOR RELIABILITY MEASUREMENTS IN MILITARY AND NASA SPECIFICATIONS |
EETC REPORT #3 | RELIABILITY INDOCTRINATION THROGH EDUCATION |
EETC REPORT #30 | STANDARD ACCELEROMETER TERMINOLOGY |
EETC REPORT #31 | NUCLEAR RADIATION ENVIRONMENT |
EETC REPORT #32 | THE EFFECTS OF SPACE ENVIRONMENT RADIATION UPON CONNECTOR MATERIALS AND FINISHES |
EETC REPORT #5 | STANDARD GYRO TERMINOLOGY |
EETC REPORT #6 | ELECTRONIC COMPONENT PART STATUS AS RELATED TO SYSTEM RELIABILITY REPORT AND RECOMMENDATIONS |
EETC REPORT #7 | RELIABILITY ASPECTS OF HUMAN ENGINEERING BIBLIOGRAPHY |
EETC REPORT #8 | GUIDELINES FOR RELIABILITY PROPOSALS, SPECIFICATIONS, AND PROGRAMS |
EETC REPORT #9 | RELIABILITY SPECIFICATION TREE AND MAINTAINABILITY SPECIFICATION TREE |
EPC 60-68 | RATE-INTEGRATING GYRO TEST INSTRUCTIONS |
EPC 61-21 | PROPOSED TEST INSTRUCTIONS FOR RATE GYROS |
GCS 56-45C | SOLENOID VALVES, 3-WAY |
GCS 57-20E | REGULATORS, GAS PRESSURE |
GCS 59-38 | GAS PRESSURE RELIEF VALVES |
GCS 60-9 | CHECK VALVES |
GCS 61-28D | COUPLING ASSEMBLY, QUICK DISCONNECT MECHANICALLY OPERATED |
NA 0001-0006 | RIVET, SOLID-UNIVERSAL HEAD ALUMINUM AND ALUMINUM ALLOY, METRIC |
NA 0007 | PROCUREMENT SPECIFICATION METRIC FASTENERS, TITANIUM ALLOY, EXTERNALLY THREADED, 1100 MPA TENSILE, 660 MPA SHEAR |
NA 0008 | PROCUREMENT SPECIFICATION METRIC FASTENERS, ALLOY STEEL, EXTERNALLY THREADED, 1100 MPA TENSILE, 660 MPA SHEAR |
NA 0009 | NUTS, SELF LOCKING, 235 DEG C, METRIC, PROCUREMENT SPECIFICATION FOR |
NA 0010 | STUD AND MANDREL TEST FIXTURE SELF-LOCKING NUTS, METRIC |
NA 0011 | FIXTURE - STRESS EMBRITTLEMENT TEST SELF-LOCKING NUTS, METRIC |
NA 0012 | FIXTURE-BEARING SURFACE SQUARENESS TEST SELF-LOCKI |
NA 0013-0018 | RIVET, SOLID-COUNTERSUNK 100 DEG HEAD, ALUMINUM AND ALUMINUM ALLOY, METRIC |
NA 0019-0024 | RIVET, SOLID-COUNTERSUNK 100 DEG SHEAR HEAD, ALUMINUM AND ALUMINUM ALLOY, METRIC |
NA 0025 | RECESS - OFFSET CRUCIFORM DIMENSIONS OF RECESS, GAGE AND DRIVE, METRIC |
NA 0026 | PROCUREMENT SPECIFICATION, METRIC FASTENERS, A-286 CRES EXTERNALLYTHREADED, 1100 MPA TENSILE, 660 MPA SHEAR |
NA 0027-0028 | NUT, SELF-LOCKING, FLOATING, PLATE, TWO-LUG, METRIC LOW HEIGHT, C'BORED, 1100 MPA 235 DEG C, 425 DEG C |
NA 0029-0030 | NUT, SELF-LOCKING, SPLINE DRIVE, 1250 MPA, 235 DEG C, 425 DEG C, METRIC |
NA 0031-0032 | NUT, SELF-LOCKING, PLATE, ONE LUG, METRIC, FIXED LOW HEIGHT, C'BORED, 1100 MPA 235 DEG C, 425 DEG C |
NA 0033-0034 | NUT, SELF-LOCKING, HEXAGON EXTENDED WASHER 1100 MPA, METRIC, 235 DEG C, 425 DEG C |
NA 0035 | SCREW, CLOSE TOLERANCE PAN HEAD OFFSET CRUCIFORM RECESS ALLOY STEEL, 1100 MPA, METRIC |
NA 0036 | BOLT, CLOSE TOLERANCE, HEXAGON HEAD ALLOY STEEL 1100 MPA METRIC |
NA 0037 | BOLT, CLOSE TOLERANCE, HEXAGON HEAD, TITANIUM ALLOY, 1100 MPA METRIC |
NA 0038 | SCREW, CLOSE TOLERANCE, 100 DEG FLUSH HEAD OFFSET CRUCIFORM RECESS ALLOY STEEL, 660 MPA SHEAR, METRIC |
NA 0039 | SCREW, CLOSE TOLERANCE, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM RECESS, TITANIUM ALLOY, 660 MPA, SHEAR, METRIC |
NA 0040-0041 | NUT, SELF-LOCKING, PLATE, TWO LUG, FIXED LOW HEIGHT, C'BORED, 1100 MPA, METRIC, 235 DEG C, 425 DEG C |
NA 0042 | SCREW, CLOSE TOLERANCE, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM RECESS, A-286 CRES, 660 MPA SHEAR, METRIC |
NA 0043 | IDENTIFICATION OF MALE THREADED FASTENERS METRIC |
NA 0044 | NUT, SELF LOCKING, 425 DEG C, METRIC, PROCUREMENT SPECIFICATION FOR |
NA 0045 | BOLT, CLOSE TOLERANCE, HEXAGON HEAD, A-286 CRES, 1100 MPA METRIC |
NA 0046 | SCREW, CLOSE TOLERANCE PAN HEAD, OFFSET CRUCIFORM RECESS, A-286 CRES, 1100 MPA METRIC |
NA 0047 | SCREW, CLOSE TOLERANCE PAN HEAD, OFFSET CRUCIFORM RECESS, TITANIUMALLOY, 1100 MPA, METRIC |
NA 0048 | GAGING OF FLUSH HEAD METRIC THREADED FASTENERS BY THE PROTRUSION METHOD |
NA 0049 | NUT, SELF-LOCKING, CASTELLATED REDUCED HEXAGON, 600 MPA METRIC, 235 DEG C |
NA 0050 | NUT, SELF-LOCKING, CASTELLATED, REDUCED HEXAGON, 1100 MPA TENSILE, METRIC, 235 DEG C |
NA 0051 | RIVET - SOLID, UNIVERSAL HEAD, A286 CORROSION RESISTANT STEEL, METRIC |
NA 0052 | RIVET - SOLID, UNIVERSAL HEAD, MONEL, METRIC |
NA 0053 | RIVET - SOLID, COUNTERSUNK 100 DEG HEAD, A286 CORROSION RESISTANT STEEL, METRIC |
NA 0054 | RIVET - SOLID, COUNTERSUNK 100 DEG HEAD, MONEL, METRIC |
NA 0055 | RIVET - SOLID, REDUCED COUNTERSUNK 100 DEG HEAD, A286 CORROSION RESISTANT STEEL, METRIC |
NA 0056 | RIVET - SOLID, REDUCED COUNTERSUNK 100 DEGR HEAD, MONEL, METRIC |
NA 0057 | PROCUREMENT SPECIFICATION, METRIC FASTENERS, ALLOY STEEL, EXTERNALLY THREADED, 1250 MPA TENSILE, 750 MPA SHEAR |
NA 0058 | BOLT, CLOSE TOLERANCE, SPLINE DRIVE, ALLOY STEEL, 1250 MPA, METRIC |
NA 0059 | BOLT, CLOSE TOLERANCE, SPLINE DRIVE, A286 CRES, 1250 MPA METRIC |
NA 0060 | SCREW, CLOSE TOLERANCE, 100 DEGREES FLUSH HEAD, OFFSET CRUCIFORM RECESS ALLOY STEEL 750 MPA SHEAR, METRIC |
NA 0061 | NUT, SELF-LOCKING, SPLINE DRIVE, ALLOY STEEL, 1800 MPA, 235 DEG C,METRIC |
NA 0062 | BOLT, CLOSE TOLERANCE, SPLINE DRIVE, ALLOY STEEL, 1550 MPA, METRIC |
NA 0063 | BOLT, CLOSE TOLERANCE, SPLINE DRIVE, ALLOY STEEL, 1800 MPA, METRIC |
NA 0064-0066 | NUT, THIN, WITH OPTIONAL LOCKWIRE HOLE, METRIC |
NA 0067 | SCREW, DUAL, WRENCHING, HEX HEAD/OFFSET CRUCIFORM, A286 CRES, FULLTHREAD, 1100 MPA - METRIC |
NA 0068 | SCREW, MACHINE, PAN HEAD, OFFSET CRUCIFORM, A286 CRES FULL THREAD 1100 MPA - METRIC |
NA 0069 | SCREW, CAP, SOCKET HEAD, FULL THREAD A-286, 1100 MPA, METRIC |
NA 0070 | SCREW, MACHINE, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM RECESS, FULL THREAD, A286 CRES, 1100 MPA, METRIC |
NA 0071 | BOLT, ALLOY STEEL 1550 MPA TENSILE, PROCUREMENT SPECIFICATION |
NA 0072 | BOLT, ALLOY STEEL 1800 MPA TENSILE, PROCUREMENT SPECIFICATION |
NA 0073-0074 | NUT, SELF-LOCKING, PLATE, ONE LUG, METRIC, FLOATING LOW HEIGHT, C'BORED, 1100 MPA 235 DEG C, 425 DEG C |
NA 0075-0076 | NUT, CAPTIVE WASHER, SHEAR TYPE, SELF-LOCKING C'BORED, 1100 MPA, METRIC 235 DEG C AND 425 DEG C |
NA 0077 | NUT, SELF-LOCKING, PLATE, FIXED, ONE LUG, STEEL, REDUCED RIVET SPACING, LOW HEIGHT, CBORE, 1100 MPA, METRIC, 235 DEG C |
NA 0077-0078 | NUT, SELF-LOCKING, PLATE, FIXED, ONE LUG REDUCED RIVET SPACING, LOW HEIGHT, C'BORED, 1100 MPA, METRIC 235 DEG C, 425 DEG C |
NA 0078 | NUT, SELF-LOCKING, PLATE, FIXED, ONE LUG, CRES, REDUCED RIVET SPACING, LOW HEIGHT, CBORE, 900 MPA, METRIC, 235 DEG C AND 425 DEG C |
NA 0079 | NUT, SELF-LOCKING, PLATE, FIXED, TWO LUG, STEEL, REDUCED RIVET SPACING, LOW HEIGHT, CBORE, 1100 MPA, METRIC, 235 DEG C |
NA 0079-0080 | NUT, SELF-LOCKING, PLATE, FIXED, TWO LUG REDUCED RIVET SPACING, LOW HEIGHT, C'BORED, 1100 MPA, METRIC 235 DEGREES C, 425 DEGREES C |
NA 0080 | NUT, SELF-LOCKING, PLATE, FIXED, TWO LUG, CRES, REDUCED RIVET SPACING, LOW HEIGHT, CBORE, 900 MPA, METRIC, 235 DEG C, AND 425 DEG C |
NA 0081 | NUT, SELF-LOCKING, PLATE, FIXED, CORNER, STEEL, REDUCED RIVET SPACING, LOW HEIGHT, CBORE, 1100 MPA, METRIC, 235 DEG C |
NA 0081-0082 | NUT, SELF-LOCKING, PLATE, FIXED, CORNER REDUCED RIVET SPACING, LOW HEIGHT, C'BORED, 1100 MPA, METRIC 235 DEGREES C, 425 DEGREES C |
NA 0082 | NUT, SELF-LOCKING, PLATE, FIXED, CORNER, CRES, REDUCED RIVET SPACING, LOW HEIGHT, CBORE, 900 MPA, METRIC 235 DEG C AND 425 DEG C |
NA 0083 | NUT, SELF-LOCKING, PLATE, FIXED, SIDE BY SIDE, STEEL, REDUCED RIVET SPACING, LOW HEIGHT, CBORE, 1100 MPA, METRIC, 235 DEG C |
NA 0083-0084 | NUT, SELF-LOCKING, PLATE, FIXED, SIDE BY SIDE REDUCED RIVET SPACING, LOW HEIGHT, C'BORED, 1100 MPA, METRIC 235 DEGREE C, 425 DEGREE C |
NA 0084 | NUT, SELF-LOCKING, PLATE, FIXED, SIDE BY SIDE, CRES REDUCED RIVET SPACING, LOW HEIGHT, CBORE, 900 MPA, METRIC, 235 DEG C AND 425 DEG C |
NA 0085-0086 | NUT, SELF-LOCKING, PLATE, FLOATING, TWO LUG REDUCED RIVET SPACING, LOW HEIGHT, C'BORED, 1100 MPA, METRIC 235 DEG C, 425 DEG C |
NA 0087-0088 | NUT, SELF-LOCKING, PLATE, FLOATING, SIDE BY SIDE, REDUCED RIVET SPACING, LOW HEIGHT, C'BORED, 900 MPA, METRIC 235 DEG C, 425 DEG C |
NA 0089 | SCREW, PAN HEAD, OFFSET CRUCIFORM RECESS FULL THREAD, ALLOY STEEL, 1100 MPA, METRIC |
NA 0090 | SCREW, PAN HEAD, OFFSET CRUCIFORM RECESS, FULL THREAD, TITANIUM ALLOY, 1100 MPA METRIC |
NA 0091 | SCREW, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM RECESS, FULL THREAD, ALLOY STEEL, 1100 MPA, METRIC |
NA 0092 | SCREW, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM RECESS, FULL THREAD, TITANIUM ALLOY, 1100 MPA, METRIC |
NA 0093-0094 | NUT, SELF-LOCKING, FLOATING, PLATE, CORNER LOW HEIGH, C'BORED, 1100 MPA, METRIC, 235 DEG C, 425 DEG C |
NA 0095 | NUT, SELF-LOCKING, PLATE, CORNER, STEEL, LOW HEIGHT, CBORE, 1100 MPA, METRIC, 235 DEG C |
NA 0095-0096 | NUT, SELF-LOCKING, PLATE, CORNER LOW HEIGHT, C'BORED, 1100 MPA, METRIC 235 DEGREE C, 425 DEGREE C |
NA 0096 | NUT, SELF-LOCKING, PLATE, CORNER, CRES, LOW HEIGHT, CBORE, 900 MPA, METRIC, 235 DEG C AND 425 DEG C |
NA 0100 | FASTENER CODE, METRIC |
NA 0113 | SCREW, HEX HEAD OFFSET CRUCIFORM TITANIUM, FULL THREAD, 1100 MPA, METRIC |
NA 0114 | SCREW, HEX HEAD OFFSET CRUCIFORM ALLOY STEEL, FULL THREAD, 1100 MPA, METRIC |
NA 0115 | ANGLE, PLAIN-EXTRUDED, ALUMINUM ALLOY, METRIC |
NA 0116 | ANGLE, BULB - EXTRUDED, ALUMINUM ALLOY, METRIC |
NA 0117 | CHANNEL-EXTRUDED, ALUMINUM ALLOY, METRIC |
NA 0118 | TEE-EXTRUDED, ALUMINUM ALLOY, METRIC |
NA 0119-0120 | BRACKET, 90 DEG ANGLE, 2-BOLT ATTACH, METRIC |
NA 0121-0122 | BRACKET, 90 DEGREE ANGLE, 2-RIVET ATTACH, METRIC |
NA 0123 | SCREW, CLOSE TOLERANCE, 100 DEG REDUCED CROWN HEAD, OFFSET CRUCIFORM RECESS, ALLOY STEEL, 660 MPA SHEAR, METRIC |
NA 0124 | SCREW, CLOSE TOLERANCE, 100 DEG REDUCED CROWN HEAD, OFFSET CRUCIFORM RECESS, A-286 CRES, 660 MPA SHEAR, METRIC |
NA 0125 | SCREW, CLOSE TOLERANCE, 100 DEG REDUCED CROWN HEAD, OFF SET CRUCIFORM RECESS, TITANIUM, 660 MPA SHEAR, METRIC |
NA 0126 | BOLT, ADJUSTING, CROWN HEXAGON HEAD, ALLOY STEEL, FULL THREAD, 1100 MPA, METRIC |
NA 0127 | SCREW, CAPTIVE, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM RECESS, ALLOY STEEL, 660 MPA SHEAR, METRIC |
NA 0128 | SCREW, CAPTIVE, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM RECESS, A-286 CRES, 660 MPA SHEAR, METRIC |
NA 0129 | SCREW, CAPTIVE, 100 DEG FLUSH HEAD, OFFSET CRUCIFORM RECESS, TITANIUM, 660 MPA SHEAR, METRIC |
NA 0130 | SCREW, CAPTIVE, PAN HEAD, OFFSET CRUCIFORM RECESS, ALLOY STEEL, 660 MPA SHEAR, METRIC |
NA 0131 | SCREW, CAPTIVE, PAN HEAD, OFFSET CRUCIFORM RECESS, A-286 CRES, 660MPA SHEAR, METRIC |
NA 0132 | SCREW, CAPTIVE, PAN HEAD, OFFSET CRUCIFORM RECESS, TITANIUM, 660 MPA SHEAR, METRIC |
NA 0133 | NUT, SELF-LOCKING, BARREL, FLOATING, 1550 MPA, METRIC |
NA 0134 | RETAINER, NUT, FLOATING BARREL, METRIC |
NA 0135 | KEY, MACHINE, SQUARE CROSS SECTION, BOTH ENDS SQUARE, ALLOY STEEL,METRIC |
NA 0136 | KEY, MACHINE, SQUARE CROSS SECTION, BOTH ENDS SQUARE, CRES STEEL, METRIC |
NA 0137 | KEY, WOODRUFF, ALLOY STEEL, METRIC |
NA 0138 | KEY, WOODRUFF, CRES STEEL, METRIC |
NA 0139 | KEYWAY AND KEY SLOT DIMENSIONS, METRIC |
NA 0140-0144 | WASHER, DIMPLED, 100 DEG, METRIC |
NA 0145 | INSERT, SCREW THREAD, KEY LOCKED, INSTALLATION AND REMOVAL PROCEDURE, METRIC |
NA 0146 | INSERT, SCREW THREAD KEY LOCKED, ALLOY STEEL, MINIATURE, METRIC |
NA 0147 | INSERT, SCREW THREAD KEY LOCKED, A286 CRES MINIATURE, METRIC |
NA 0148 | INSERT, SCREW THREAD KEY LOCKED, ALLOY STEEL, LIGHTWEIGHT, METRIC |
NA 0149 | INSERT, SCREW THREAD KEY LOCKED, A286 CRES LIGHTWEIGHT, METRIC |
NA 0150 | INSERT, SCREW THREAD KEY LOCKED, ALLOY STEEL, HEAVY DUTY, METRIC |
NA 0151 | INSERT, SCREW THREAD KEY LOCKED, A286 CRES HEAVY DUTY, METRIC |
NA 0152 | BOLT, EYE, ALLOY STEEL, 1100 MPA, METRIC |
NA 0153 | BOLT, EYE, A286 CRES, 1100 MPA, METRIC |
NA 0154 | RIVETS, SOLID, ALUMINUM AND ALUMINUM ALLOY, METRIC, PROCUREMENT SPECIFICATION FOR |
NA 0155 | BOLT, CLEVIS, 660 MPA SHEAR, METRIC |
NA 0156 | MALE THREADED FASTENERS, METRIC DESIGN, PARAMETERS FOR |
NA 0157-0158 | PIN, QUICK RELEASE, SELF-RETAINING, POSITIVE LOCKING, SINGLE ACTING, "T" HANDLE, METRIC |
NA 0159 | SCREW, FAIRING WASHER, ASSEMBLY, ALLOY STEEL, OFFSET CRUCIFORM RECESS, FULL THREAD, 1100 MPA TENSILE, METRIC |
NA 0160 | SCREW, FAIRING WASHER, ASSEMBLY, 6AL-4V TITANIUM ALLOY, OFFSET CRUCIFORM RECESS, FULL THREAD, 1100 MPA TENSILE, METRIC |
NA 0161 | PIN, QUICK RELEASE, POSITIVE LOCKING SINGLE ACTING, METRIC, PROCUREMENT SPECIFICATION FOR |
NA 0162 | SETSCREW, HEXAGON SOCKET, CUP POINT, A286 CRES, METRIC |
NA 0163 | BOLT, BLIND, DESIGN ELEMENTS, METRIC |
NA 0164 | SPACER, SLEEVE, SWAG TYPE, METRIC |
NA 0165 | POST, ELECTRICAL-MECHANICAL EQUIPMENT, SWAGE TYPE, METRIC |
NA 0166-0167 | INSERT, MOLDED-IN, CSK CLEARANCE HOLE, SANDWICH PANEL, AL ALLOY AND CRES, METRIC |
NA 0168-0169 | INSERT, MOLDED-IN, THRU CLEARANCE HOLE, SANDWICH PANEL, AL ALLOY AND CRES, METRIC |
NA 0174 | DESIGN PARAMETERS FOR HEAD FORM OF SOLID RIVETS AND 100 DEG REDUCED HEAD FOR BOLTS, METRIC |
NA 0175-0177 | SPACER, SLEEVE-NON METALLIC SCREW AND BOLT, METRIC |
NA 0179 | WASHER, PLAIN AND COUNTERSUNK, METRIC |
NA 0180-0183 | SPACER, SLEEVE-SCREW AND BOLT, METRIC |
NA 0184 | NUT SPACER, PLATE-UNIVERSAL, METRIC |
NA 0190-0193 | SPACER, SLEEVE-RIVET, METRIC |
NA 0201-0204 | POST, ELECTRICAL-MECHANICAL EQUIPMENT, STUD TYPE, METRIC |
NA 0211-0212 | POST, ELECTRICAL - MECHANICAL EQUIPMENT, SWAGE TYP |
NA 0211-0213 | POST, ELECTRICAL-MECHANICAL EQUIPMENT, SWAGE TYPE, METRIC |
NA 0221-0224 | POST, ELECTRICAL-MECHANICAL EQUIPMENT, INTERNAL THREAD TYPE, METRIC |
NA 0231-0233 | SPACER, STEPPED, SWAGE TYPE, METRIC |
NA 0235-0236 | INSERT, SANDWICH PANEL, MOLDED IN, CSK, THRU CLEARANCE, AL ALLOY/CRES, METRIC |
NA 0237-0238 | INSERT, SANDWICH PANEL, MOLDED IN, THRU CLEARANCE, AL ALLOY/CRES, METRIC |
NA 0241 | INSERT, SANDWICH PANEL, MOLDED IN, BLIND THREADED, SELF-LOCKING, CRES, LIGHTWEIGHT, METRIC |
NA 0242 | INSERT, SANDWICH PANEL, MOLDED IN, THRU THREADED, SELF-LOCKING, CRES, METRIC |
NA 0243 | INSERT, SANDWICH PANEL, MOLDED IN, BLIND THREADED, SELF-LOCKING, CRES, METRIC |
NA 0244 | INSERT, SANDWICH PANEL, MOLDED IN, BLIND THREADED, SELF-LOCKING, ALUM/STEEL, FLOATING, METRIC |
NA 0245 | INSERT, SANDWICH PANEL, MOLDED IN, BLIND THREADED, SELF-LOCKING, CRES/CRES, FLOATING, METRIC |
NA 0246 | BALLS, BEARING, CHROME ALLOY STEEL METRIC |
NA 0247 | BEARING, PLAIN, SELF LUBRICATING, SELF-ALIGNING LOW SPEED, NARROW,GROOVED OUTER RING, -54 DEG C TO 163 DEG C, METRIC |
NA 0248 | BEARING, PLAIN, SELF LUBRICATING, SELF-ALIGNING LOW SPEED, NARROW,CHAMFERED OUTER RING, -54 DEG C TO 163 DEG C, METRIC |
NA 0249 | BEARING, PLAIN, SELF LUBRICATING, SELF-ALIGNING LOW SPEED, WIDE, GROOVE OUTER RING, -54 DEG C TO 163 DEG C, METRIC |
NA 0250 | BEARING, PLAIN, SELF LUBRICATING, SELF-ALIGNING LOW SPEED, WIDE, CHAMFERED OUTER RING, -54 DEG C TO 163 DEG C, METRIC |
NA 0252 | BOLT, SHOULDER, HEXAGON HEAD, A286 CRES, 1100 MPA TENSILE, METRIC |
NA 0253 | BOLT, SHOULDER, HEXAGON HEAD, ALLOY STEEL, 1100 MPA TENSILE, METRIC |
NA 0258 | PROCUREMENT SPECIFICATION BOLT, METRIC, SELF-RETAINED, IMPEDANCE TYPE, 660 MPA SHEAR |
NA 0269 | BUSHING - SLEEVE, FLANGED, PRESS FIT, REAM TYPE, METRIC |
NA 0270 | BUSHING - SLEEVE, PLAIN, PRESS FIT, REAM TYPE, METRIC |
NA 0271 | PROCUREMENT SPECIFICATION, METRIC FASTENERS, CRES 300 SERIES, EXTERNALLY THREADED, MJ THREAD, 500 MPA FTU AND 700 MPA FTU |
NA 0272 | BOLT, CLOSE TOLERANCE, HEXAGON HEAD, 300 SERIES CRES, 500 MPA FTU, METRIC |
NA 0273 | SCREW, PAN HEAD, OFFSET CRUCIFORM RECESS DRIVE, FULL THREAD, CRES, 500 MPA FTU, METRIC |
NA 0274 | SCREW, CAP, SOCKET HEAD, FULL THREAD, 300 SERIES CRES, 500 MPA FTU, METRIC |
NAM 1312-105 | FASTENER TEST METHODS METRIC, METHOD 105, STRESS DURABILITY |
NAM 1312-107 | FASTENER TEST METHODS, METRIC, METHOD 107, VIBRATION |
NAM 1312-108 | FASTENER TEST METHODS, METRIC METHOD 108 TENSILE STRENGTH |
NAM 1312-109 | FASTENER TEST METHODS, METRIC, METHOD 109 STRESS CORROSION |
NAM 1312-111 | FASTENER TEST METHODS, METRIC METHOD 111 TENSION FATIGUE |
NAM 1312-113 | FASTENER TEST METHODS, METRIC, METHOD 113 DOUBLE SHEAR TEST |
NAM 14289 | STRAP, RETAINING, CUSHIONED, RECTANGULAR, TWO-PIECE, METRIC |
NAM 14290 | CLAMP, LOOP, CUSHIONED, RECTANGULAR, METRIC |
NAM 51417 | BOLT, MACHINE, HEX HEAD, FULLY THREADED, FINE THREAD, METRIC |
NAM 51474 | SCREW, CAP, HEX HEAD, FULLY THREADED - METRIC |
NAS 1 | RIVET - COUNTERSUNK HEAD 100 DEGREE |
NAS 10 | STANDARD FORM FOR NATIONAL AIRCRAFT STANDARD DRAWINGS |
NAS 100 | ROD ASSEMBLY - CONTROL, WELDED TUBE, 3/8 O.D., STEEL, 1/4 ADJUSTABLE BEARING ENDS |
NAS 1000 | TUBE END-STANDARD DIMENSIONS FOR INSIDE DOUBLE FLAIRE |
NAS 10000 | NA DOCUMENTS PREPARATION AND MAINTENANCE IN SI (METRIC) UNITS |
NAS 10001 | PREFERRED METRIC UNITS FOR AEROSPACE |
NAS 10008 | PROCUREMENT SPECIFICATION METRIC FASTENERS, TITANIUM ALLOY EXTERNALLY THREADED 1100 MPA TENSILE 660 MPA SHEAR |
NAS 10009 | PROCUREMENT SPECIFICATION METRIC FASTENERS, ALLOY STEEL EXTERNALLYTHREADED 1100 MPA TENSILE 660 MPA SHEAR |
NAS 1001 | TUBE END-STANDARD DIMENSIONS FOR OUTSIDE DOUBLE FLARE |
NAS 10010 | NUTS, SELF-LOCKING, 235 DEGREES C, HIGH QUALITY, METRIC |
NAS 10011 | STUD AND MANDREL TEST FIXTURE SELF-LOCKING NUTS, METRIC |
NAS 10012 | FIXTURE - STRESS EMBRITTLEMENT TEST SELF-LOCKING NUTS, METRIC |
NAS 10013 | FIXTURE- BEARING SURFACE SQUARENESS TEST SELF-LOCKING NUTS, METRIC |
NAS 1002 | STUD, ELECTRICAL, TERMINAL BLOCK |
NAS 1003-1020 | BOLT - MACHINE HEXAGON HEAD, A286 CRES |
|
