Popular Standards |
|
GME L-3A/4A-6 | FATIGUE TEST OF PINION THRUST WASHER IN THE DIFFERENTIAL CASE |
GME L-3A01-3 | BELLOWS - OUTSIDE, AXLE SHAFT - FWD/DURABILITY TEST ON THE TEST STAND THIS SPECIFICATION MAY BE APPLIED ONLY FOR |
GME L-3A04-1 | DURABILITY TEST OF HOMOKINETIC JOINTS, AXLE SHAFT FWD |
GME L-3A04-3 | HOMOKINETIC JOINTS FOR AXLE SHAFTS-FWD/RWD, DURABILITY BENCH TEST *THIS SPECIFICATION MAY BE APPLIED ONLY FOR |
GME L-3A04-4 | BELLOW-INNER, AXLE SHAFT FWD, DURABILITY TEST ON THE TEST BENCH |
GME L-3A1-3 | DURABILITY TEST OF THE FRONT AXLE OUTER BOOT, RIG. TEST |
GME L-3A2-1 | FATIGUE TEST OF FWD AXLE SHAFTS AND JOINTS |
GME L-3A4-2 | FATIGUE TEST OF FWD AXLE SHAFT BOOTS (HOT AND COLD TEST) |
GME L-3B-1 | LIP SEALS FOR WHEEL HUBS |
GME L-3B/4A5-1 | HUB UNIT WHEEL BEARINGS FOR INGRESS OF WATER |
GME L-3B/4A5-2 | WHEEL BEARING TEST (EXCEPT FOR RIGID AXLES) |
GME L-3B/4A5-3 | FRICTIONAL TORQUE OF WHEEL BEARINGS |
GME L-3C-01 | SYSTEM TEST OF FRONT AND REAR SUSPENSION SPRINGS |
GME L-3C-3 | FATIGUE TEST OF MACPHERSON STRUTS AND STRUT CARTRIDGES |
GME L-3C/4C-2 | DYNAMIC TEST OF DAMPING RINGS (SPRING SEAT) |
GME L-3E/4D-1 | FATIGUE TEST FOR REBOUND BUMPERS OF HYDRAULIC VIBRATION DAMPERS ***THIS STANDARD MAY BE APPLIED ONLY FOR CURRENT |
GME L-3F-3 | SHOCK ABSORBER ATTACHMENT |
GME L-3F/4E-1 | FATIGUE TEST FOR RIDE CONTROL STRUTS AND SHOCK ABSORBERS |
GME L-3F/4E-2 | FATIGUE TEST OF HYDRAULIC SHOCK ABSORBERS |
GME L-3F/4E-3 | MORNING KNOCK |
GME L-3G-1 | FATIGUE TEST OF PLASTIC STABILIZER LINKS |
GME L-3G-3 | FATIGUE TEST OF HINGED TIE BAR AND HINGED TIE BAR BRACKET, CONNECTION OF STABILIZER BAR AND STRUT TUBE |
GME L-3G/4F-1 | STABILIZER, BEARING |
GME L-3G/4F-2 | DURABILITY TEST OF STABILIZERS IN AN AXLE SYSTEM |
GME L-4A-2 | AUTOMATIC VEHICLE LEVEL CONTROL SYSTEM |
GME L-4A-3 | AUTOMATIC VEHICLE LEVEL CONTROL SYSTEM (DRAWING NO. V SPECIAL, V CAR 22 073 177, J CAR 22 073 175) |
GME L-4A01-18 | ROTATION BENDING AND TORSIONAL TEST OF REAR WHEEL SPINDLE |
GME L-4A1-1 | FATIGUE TEST OF REAR AXLE GEARING |
GME L-4A1-10 | DYNAMIC FUNCTION TEST LIMITED SLIP DIFFERENTIAL |
GME L-4A1-11 | COLD START TEST, REAR AXLE |
GME L-4A1-16 | FATIGUE TEST HOMOGKINETIC JOINT, AXLE SHAFT RWD |
GME L-4A1-17 | DURABILITY TEST OF BELLOWS DRIVE SHAFT, REAR AXLE RWD |
GME L-4A1-2 | FATIGUE TEST, BEVEL GEARS, DIFFERENTIAL |
GME L-4A1-3 | EXAMINATION OF REAR AXLE OIL |
GME L-4A1-4 | DIFFERENTIAL CASE (FATIGUE TEST) |
GME L-4A1-5 | DEFORMATION TEST OF REAR AXLE TRANSMISSION |
GME L-4A1-6 | FATIGUE TEST OF REAR AXLE BEARINGS |
GME L-4A1-7 | STATIC FUNCTION TEST LIMITED SLIP DIFFERENTIAL |
GME L-4A4-1 | DURABILITY TEST BELLOWS PROPELLER SHAFT |
GME L-4A4-3 | FATIGUE TEST OF HOMOCINETIC JOINT PROPELLER SHAFT RWD |
GME L-4A5-1 | LEAKAGE TEST OF SEALED ROLLER BEARINGS |
GME L-4E-1 | REAR AXLE DAMPERS (DYNAMIC DURABILITY) |
GME L-5-1 | DURABILITY TEST OF BRAKE BOOSTERS, BRAKE PROPORTIONING VALVES, CALIPERS AND SLAVE CYLINDERS |
GME L-5-2 | COLD TEST OF BRAKE SLEEVES |
GME L-5-3 | CLEARANCE CONDITIONS OF BRAKE COMPONENTS |
GME L-5-4 | PLOTTING OF PEDAL FORCE DIAGRAMS |
GME L-5-6 | EVALUATION OF BRAKE SADDLE RIGIDITY |
GME L-5-8 | ELASTIC DEFORMATION OF THE DASH WALL |
GME L-5-9 | BRAKE PEDAL DURABILITY AND DEFORMATION TEST **THIS SPECIFICATION MAY BE APPLIED ONLY FOR CURRENT PROJECTS INCL. GLOBAL EPS |
GME L-5A-10 | INERTIA DYNAMOMETER TEST OF BRAKE SYSTEMS WITH VENTILATED BRAKE DISKS |
GME L-5A/B-1 | VIBRATION TEST, BRAKE CALIPER |
GME L-5A/B-11 | QUALITY CONTROL OF DISK BRAKE PADS |
GME L-5A/B-12 | AK-MASTER TEST SCHEDULE |
GME L-5A/B-3 | INERTIA DYNAMOMETER BRAKE TEST |
GME L-5A/B-4 | BRAKE ROTOR EROSION SCHEDULE ON THE COEFFICIENT OF FRICTION TEST STAND |
GME L-5A/B-6 | CAP WHEEL BRAKE CYLINDER |
GME L-5D-2 | PARKING BRAKE DURABILITY DEFORMATION AND EFFICIENCY TEST THIS STANDARD MAY BE APPLIED ONLY FOR CURRENT PROJECTS INCL. GL |
GME L-5F-1 | BRAKE HOSE - WIP TEST |
GME L-5F-2 | BRAKE HOSES BURST PRESSURE TEST |
GME L-5F-4 | BRAKE HOSES - HEAT RESISTANCE OF CONNECTIONS |
GME L-5F-6 | HOTPLATE TEST FOR BRAKE HOSES |
GME L-5F-7 | COMBINATION TEST ON BRAKE HOSES (FORMERLY GMI L-5F-7) |
GME L-5G-1 | VACUUM HOSE FOR BRAKE BOOSTER |
GME L-6-1 | ENGINE RUN-IN OHC-ENGINES |
GME L-6-10 | DETERMINATION OF ENGINE MOUNT LOADS |
GME L-6-14 | COLD START AND CRANKING TESTS ON DIESEL ENGINES |
GME L-6-2 | ENGINE RUN-IN CIH-ENGINES |
GME L-6-21 | MAIN AXLES OF INERTIA AND STRONG POINT OF AXYMMETRICAL NON-HOMOGENEOUS BODIES |
GME L-6-22 | COP DIESEL SMOKE |
GME L-6-23 | COP ENGINE POWER |
GME L-6-3 | COLD START AND CRANKING TESTS ON SPARK IGNITION ENGINES |
GME L-6-40 | DETERMINATION OF EXHAUST GAS RECIRCULATION RATE (EGR) |
GME L-6-41 | EXHAUST GAS RECIRCULATION RATE (EGR) - MIXTURE DISTRIBUTION |
GME L-6-42 | 3 H FULL LOAD SHORT RUN-IN PROGRAM FOR A GASOLINE ENGINE ON THE TEST STAND |
GME L-6-43 | DETERMINING THE AIR/FUEL RATIO IN FULL AND PART LOAD OF AN ENGINE ON THE ENGINE TEST STAND |
GME L-6-44 | AUTOMATIC TARGETING OF MAP POINTS |
GME L-6-45 | DEVELOPMENT OF THE CRANKCASE VENTILATION OF AN ENGINE ON THE ENGINE TEST STAND |
GME L-6-46 | MEASUREMENT OF THE ABSOLUTE IDLE SPEED FUEL CONSUMPTION OF AN ENGINE ON THE ENGINE TEST STAND |
GME L-6-47 | STANDARD POINT MEASUREMENT ON THE ENGINE TEST STAND |
GME L-6-48 | DETERMINING THE DRAG POWER OF AN ENGINE ON THE ENGINE TEST STAND |
GME L-6-49 | DETERMINING THE FULL LOAD NET POWER OF AN ENGINE ON THE ENGINE TEST STAND |
GME L-6-50 | WARM-UP AND LEARNING PROCEDURE |
GME L-6-51 | IGNITION CURVES |
GME L-6-52 | DETERMINING THE OPTIMUM IGNITION OF AN ENGINE ON THE ENGINE TEST STAND |
GME L-6-53 | DETERMINING THE FUEL CONSUMPTION OF AN ENGINE ON THE ENGINE TEST STAND - ROAD PART LOAD CONSUMPTION |
GME L-6-54 | REAR SIDE WAVINESS OF TOOTHED BELTS |
GME L-6-6 | BLUE SMOKE TEST |
GME L-6A02-1 | DURABILITY BENCH TEST OF CYLINDER HEAD GASKETS |
GME L-6A02-3 | CYLINDER DISTORTION MEASUREMENT *** MISSING PAGE #9, VENDOR WILL SEND REPLACMENT WHEN AVAILABLE ** |
GME L-6A02-4 | LEAKTEST WITH INCREASED COOLING SYSTEM PRESSURE |
GME L-6A02-7 | DISTRIBUTION OF SURFACE PRESSURE |
GME L-6A02-9 | THICKNESS MEASUREMENT OF CYLINDER HEAD GASKETS |
GME L-6A1-1 | BEHAVIOUR OF ENGINE OILS IN THE POSITIVE CRANKCASE VENTILATION SYSTEM OF THE 1.3 OHC ENGINE |
GME L-6A2-10 | EVALUATION OF KNOCK CONTROL SYSTEMS |
GME L-6A2-2 | COLD-HOT TEST FOR CYLINDER HEAD GASKETS |
GME L-6A2-3 | CYLINDER DISTORTION MEASUREMENT |
GME L-6A2-5 | TEST OF CYLINDER HEAD GASKET KNOCKING COMBUSTION |
GME L-6A2-6 | NITROGEN TEST OF CYLINDER HEAD GASKETS |
GME L-6A2-8 | OPERATION ORIENTED DESIGN OF INTAKE COMPONENTS OF FOUR-STROKE INDUCTIVE ENGINES |
GME L-6A3-1 | DETERMINATION OF ENGINE COMPRESSION RATIO |
