Popular Standards |
|
GME L-6B-1 | ENGINE IDENTIFICATION |
GME L-6C-1 | CRANKSHAFT FATIGUE TEST - SURVEY |
GME L-6C-2 | CRANKSHAFT GUIDE BEARINGS |
GME L-6C3/K1-1 | FLYWHEEL AND FAN, BURST STRENGTH |
GME L-6D-3 | FATIGUE TEST OF CONNECTING RODS ON THE PULSATOR |
GME L-6G-1 | ENGINE OIL CONSUMPTION |
GME L-6G05-1 | OIL FILTER DURABILITY TEST |
GME L-6G07-3 | IOL AGEING TEST |
GME L-6K/X-1 | TIMING BELT FATIGUE TEST |
GME L-6K02-10 | POLY V-BELT NOISES |
GME L-6K02-4 | V-BELT |
GME L-6K02-5 | V-BELT NOISES |
GME L-6K03-4 | THERMOSTATS |
GME L-6K2-1 | FATIGUE TEST OF WATER PUMPS |
GME L-6K2-12 | COLD START TEST FOR V-RIBBED BELTS |
GME L-6K2-8 | SERVICE LIFE OF V-BELT AND POLY-V-BELT UNDER DYNAMOMETER HOT IDLE CONDITIONS |
GME L-6K2-9 | MAINTENANCE-FREE V-BELT FATIGUE |
GME L-6K3-1 | DETERMINATION OF THE STATIC CHARACTERISTICS AND DURABILITY TEST OF THERMOSTATS |
GME L-6M1-1 | FLOWING OF CARBURETORS |
GME L-6M4-1 | FUEL PUMP FUNCTION TEST |
GME L-6M4-2 | FUEL PUMP DURABILITY TEST |
GME L-6M6-1 | PINTLE STROKE MEASUREMENTS ON DIESEL ENGINES |
GME L-6N2-1 | ACCELERATOR PEDAL, DURABILITY TEST |
GME L-6Q-2 | ENGINE MOUNTS |
GME L-6Q-5 | DURABILITY OF SYNTHETICS AND ELASTOMER PARTS IN COMBINATION WITH METAL PARTS |
GME L-6R-1 | DYNAMOMETER TEST OF SPARK IGNITION ENGINES |
GME L-6R-2 | TOLERANCE BAND OF COMPRESSION RATIO |
GME L-6R-3 | POROSITIES AND BLOWHOLES IN CYLINDER BLOCKS |
GME L-6T1-1 | VACUUM PUMPS FOR BRAKE BOOSTER |
GME L-6X01-3 | VALVE STEAM SEALING |
GME L-6X01-4 | TEST OF ENGINE OILS BY MEANS OF THE CAM/TAPPET OR ROCKER ARM WEAR TEST |
GME L-6X01-5 | CAMSHAFT WEAR TEST |
GME L-6X01-5-1 | CAMSHAFT WEAR TEST |
GME L-6X1-1 | VALVE SPRING TEST |
GME L-6X1-2 | DOME ROUNDNESS OF ROCKER ARM |
GME L-6X1-6 | CAMSHAFT SEIZE TEST |
GME L-6Y-1 | MISFIRING, COMPLETE TEST |
GME L-6Y-2 | SPARK KNOCK |
GME L-6Y03-1 | ENGINE WASHING |
GME L-6Y1-1 | FATIGUE TEST OF V-RIPPED BELTS |
GME L-6Y1-2 | ALTERNATOR CAPACITY AT ENGINE IDLE SPEED |
GME L-6Y2-1 | STARTER AND SOLENOID SWITCH |
GME L-6Y3-3 | DISTRIBUTOR CAP AGING TEST |
GME L-7A-1 | GEAR OF MT TRANSMISSION |
GME L-7B01A-3 | FATIGUE TEST OF COVER GEAR SHIFT ON FWD TRANSMISSION CASE |
GME L-7B01B-1 | TEST PROGRAM CLUTCH ASSEMBLY |
GME L-7B01B-10 | FADING TEST CLUTCH ASSEMBLY |
GME L-7B01B-11 | WEAR TEST CLUTCH LINING |
GME L-7B01B-12 | BURST SPEED TEST CLUTCH DISK ASSEMBLY AND CLUTCH PRESSURE PLATE ASSEMBLY |
GME L-7B01B-14 | DURABILITY TEST OF CLUTCH DISK ASSEMBLY |
GME L-7B01B-16 | CLUTCH PLATE RUN-OUT |
GME L-7B01B-2 | MEASUREMENT OF THE THICKNESS OF CLUTCH LININGS |
GME L-7B01B-20 | MEASUREMENT OF FRICTION LOSSES AND TRAVEL LOSSES ON CLUTCH CABLE ASSEMBLY |
GME L-7B01B-21 | STRENGTH OF PEDAL MOUNTING AND DASH PANEL |
GME L-7B01B-22 | DURABILITY TEST CLUTCH CABLE |
GME L-7B01B-25 | LONG-TERM TESTING OF HYDRAULIC CLUTCH ACTUATOR (HCA) |
GME L-7B01B-3 | DETERMINATION OF THE DAMPING CHARACTERISTICS OF CLUTCH PLATE ASSEMBLIES |
GME L-7B01B-5 | FORCE AND DISTANCE MEASUREMENTS ON ASSEMBLY CLUTCH/CLUTCH DISK |
GME L-7B01B-7 | SURFACE MEASUREMENT OF FLYWHEEL AND PRESSURE PLATE |
GME L-7B01B-9 | SLIP AND FRICTION TEST OF CLUTCH ASSEMBLY |
GME L-7B01D-11 | REVERSE GEAR LOCK, SHIFT LEVER |
GME L-7B01D-14 | FATIGUE TEST OF FWD DRIVE TOOTHING |
GME L-7B01D-15 | EFFECTIVE TOOTH CLEARANCE MEASUREMENT ON MANUAL TRANSMISSION GEAR SETS |
GME L-7B01D-17 | FWD REVERSE GEAR BRAKE; TEST BENCH FUNCTIONAL AND FATIGUE TESTS |
GME L-7B01D-2 | DETERMINATION OF THE DYNAMIC COEFFICIENT OF FRICTION OF CONE CLUTCHES |
GME L-7B01D-4 | DURABILITY TEST OF THE COG WHEEL BEARINGS |
GME L-7B01D-5 | TRANSMISSION SYNCHRONIZATION AND INTERNAL SHIFT MECHANISM FATIGUE TEST |
GME L-7B01D-6 | TRANSMISSION DEFORMATION |
GME L-7B01D-9 | FATIGUE TEST OF EXTERNAL SHIFT MECHANISM FWD AND RWD MANUAL TRANSMISSION |
GME L-7B01E-1 | TRANSMISSION GASKETS (FUNCTIONAL AND DURABILITY TEST ON THE TEST BENCH) |
GME L-7B03-1 | DURABILITY TEST SCHEDULE D4C |
GME L-7B06-1 | QUALITY CHECK OF HEAT EXCHANGER NOTE: THIS SPECIFICATION MAY BE APPLIED ONLY FOR CURRENT PROJECTS INCL. GLOBAL |
GME L-7B1A-1 | FATIGUE TEST OF FWD TRANSAXLE CASES |
GME L-7B1A-2 | FATIGUE TEST OF BEARING PLATES OF FWD TRANSAXLE CASES |
GME L-7B1B-13 | CLUTCH PRESSURE SPRINGS |
GME L-7B1B-23 | FATIGUE TEST OF AUTOMATIC TRANSMISSION FLEX PLATES |
GME L-7B1B-4 | CLUTCH ASSEMBLY CORROSION TEST |
GME L-7B1B-6 | THROWOUT BEARING |
GME L-7B1D-1 | GEARS AND BEARINGS OF RWD MANUAL TRANSMISSION |
GME L-7B1D-10 | SHIFT LEVER BOOT DURABILITY FOR FWD AND FWD MT4 AND 5-SPEED |
GME L-7B1D-12 | TEST OF THE DRIVING AND DRIVER HELICAL GEARS-SPEEDOMETER |
GME L-7B1D-13 | DURABILITY OF NEEDLE BEARING CRANKSHAFT-INPUT SHAFT (PILOT BEARING) FWD AND RWD |
GME L-7B1D-7 | DURABILITY TEST TRANSMISSION INPUT SHAFT AND MAIN SHAFT BALL BEARING |
GME L-7B1D-8 | FATIGUE TEST OF TRANSMISSION GEARS, AXLE DRIVE AND BEARINGS IN THE FWD TRANSMISSION |
GME L-7B3C-1 | AT-MODULATOR DURABILITY TEST |
GME L-7E-1 | PBSL SYSTEM DURABILITY |
GME L-7E-2 | PBSL SYSTEM ABUSE TEST |
GME L-8A-4 | DURABILITY TEST OF FUEL TANKS AND THEIR RETAINING STRAPS |
GME L-8C-1 | DURABILITY TEST OF EXHAUST PIPE CONNECTIONS*THIS SPECIFICATION MAYBE APPLIED ONLY FOR CURRENT PROJECTS. IT IS SUPERCEDED |
GME L-8C-11 | EMISSION TEST - MINERAL WOOL |
GME L-8C-2 | EXHAUST-SYSTEM SUSPENSION DURABILITY TEST*NOTE:THIS SPECIFICATION MAY BE APPLIED ONLY FOR CURRENT PROJECTS. IT IS |
GME L-8C-3 | THERMAL SHOCK CYCLE TEST FOR MUFFLERS*NOTE:THIS SPECIFICATION MAY BE APPLIED ONLY FOR CURRENT PROJECTS. IT IS SUPERCEDED |
GME L-8C-4 | CONDENSATE EXPULSION TEST *THIS SPECIFICATION MAY BE APPLIED ONLY FOR CURRENT PROJECTS. IT IS SUPERCEDED FOR ALL FUTURE |
GME L-8C-5 | INTAKE SYSTEM - NOISE LEVEL MEASUREMENT OF ORIFICE NOISE & SURFACERADIATION NOTE:THIS SPECIFICATION MAY BE APPLIED ONLY |
GME L-8C-6 | MUFFLER - SUBJECTIVE EVALUATION OF OUTLET NOISE NOTE: THIS SPECIFICATION MAY BE APPLIED ONLY FOR CURRENT PROJECTS INCL. |
GME L-8C-7 | MUFFLER - SOUND LEVEL MEASUREMENT OF OUTLET NOISE NOTE: THIS SPECIFICATION MAY BE APPLIED ONLY FOR CURRENT PROJECTS INCL |
GME L-8C-8 | MUFFLER - SOUND LEVEL MEASUREMENT OF HOUSING SURFACE RADIATION NOISES NOTE: THIS SPECIFICATION MAY BE APPLIED ONLY FOR |
GME L-8C-9 | NOISE AND VIBRATION (STRUCTUREBORNE) CAUSED BY THE EXHAUST SYSTEM |
GME L-9-1 | STEERING SYSTEM IMPACT (TORSO TEST) |
GME L-9-5 | HEAD IMPACT-STEERING SYSTEM |
