Language:
    • Available Formats
    •  
    • Availability
    • Priced From ( in USD )
    • Secure PDF 🔒
    • Immediate download
    • $620.00
    • Add to Cart
    • Printed Edition
    • Ships in 1-2 business days
    • $620.00
    • Add to Cart

Customers Who Bought This Also Bought

 

About This Item

 

Full Description

Preface 

This is the eighth edition in the form of a compendium of the CSA B181 and CSA B182 series of Standards, published as CSA B1800, Thermoplastic nonpressure piping compendium . It supersedes the previous editions of the compendium, published in 2021, 2018, 2015, 2011, 2006, 2002, and 1999. This compendium consists of the following Standards: • the sixth edition of CSA B181.0, Definitions, general requirements, and methods of testing for thermoplastic nonpressure piping, which supersedes the previous editions published in 2021, 2018, 2015, 2011, and 2006; • the thirteenth edition of CSA B181.1, Acrylonitrile-butadiene-styrene (ABS) drain, waste, and vent pipe and pipe fittings, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, 1996, 1990, 1985, 1973, and 1967; • the fourteenth edition of CSA B181.2, Polyvinylchloride (PVC) and chlorinated polyvinylchloride (CPVC) drain, waste, and vent pipe and pipe fittings, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, 1996, 1990, 1987, 1985, 1973, and 1967; • the tenth edition of CSA B181.3, Polyolefin and polyvinylidene fluoride (PVDF) laboratory drainage systems, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, 1986, and 1971; • the tenth edition of CSA B181.5, Coextruded acrylonitrile-butadiene-styrene/polyvinylchloride (ABS/PVC) drain, waste, and vent pipe, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, 1995, and 1994; • the fourteenth edition of CSA B182.1, Plastic drain and sewer pipe and pipe fittings, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, 1996, 1992, 1987, 1983, 1977, and 1967; • the eleventh edition of CSA B182.2, PSM type polyvinylchloride (PVC) sewer pipe and fittings, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, 1995, 1990, and 1983; • the twelfth edition of CSA B182.4, Profile polyvinylchloride (PVC) sewer pipe and fittings, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, 1997, 1992, 1990, and 1983; • the ninth edition of CSA B182.6, Profile polyethylene (PE) sewer pipe and fittings for leak-proof sewer applications, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, and 1992; • the seventh edition of CSA B182.8, Profile polyethylene (PE) storm sewer and drainage pipe and fittings, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, and 2002; • the tenth edition of CSA B182.11, Standard practice for the installation of thermoplastic drain, storm, and sewer pipe and fittings, which supersedes the previous editions published in 2021, 2018, 2015, 2011, 2006, 2002, 1999, 1995, and 1967; • the second edition of CSA B182.12, Profile polypropylene (PP) storm sewer pipe and fittings, which supersedes the previous edition published in 2021; • the fifth edition of CSA B182.13, Profile polypropylene (PP) sewer pipe and fittings for leak-proof sewer applications, which supersedes the previous editions published in 2021, 2018, 2015, and 2011; • the fourth edition of CSA B182.14, Profile steel reinforced polyethylene (SRPE) storm sewer pipe and fittings, which supersedes the previous edition published in 2021, 2018, and 2015; and • the fourth edition of CSA B182.15, Profile steel reinforced polyethylene (SRPE) sewer pipe and fittings, which supersedes the previous edition published in 2021, 2018, and 2015. The following are the major changes to this edition: a) addition of graphitic materials to CSA B181.0 and B182.8; b) addition of DWV push-fit fittings to CSA B181.0, B181.1, and B181.2; c) revision to the relative humidity tolerance in CSA B181.0; d) revisions to the hub wall thickness measurements of moulded fittings in CSA B181.1 and B181.2; e) addition of tetrahydrofuran (THF) content requirements for solvent cements and primers in CSA B181.1, B181.2, B182.1, and B182.2; f) revisions to requirements for supports in Annex A of CSA B181.2; g) revisions to the number of specimens for dimensioning in CSA B181.3; h) addition of perforated pipe and fittings to CSA B182.2; i) removal of closed profile pipe of annular or helical construction from CSA B182.6 and B182.8; j) revisions to bending test requirements for fabricated fittings in CSA B182.6, B182.8, B182.12, B182.13, B182.14, and B182.15; k) revisions to bond strength requirements in CSA B182.6, B182.8, and B182.13; l) revisions to pipe stiffness test in CSA B182.6, B182.8, B182.12, and B182.13; m) inclusion of additional sizes for pipe stiffness in the variable class in CSA B182.8; n) clarification of recycled materials and when they can be used in CSA B182.8; o) inclusion of CSA B182.12 in Clause 1.2 of CSA B182.11; p) revisions to joint tightness test for other jointing systems in CSA B182.12; q) revisions to virgin compound requirements in CSA B182.13; and r) addition of NPS-36 to 60 sizes for open profile pipe in CSA B182.13. These Standards are considered suitable for use for conformity assessment within the stated scopes of the Standards. These Standards were prepared by the Technical Committee on Plastic Nonpressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and have been formally approved by the Technical Committee. These Standards have been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. They have been published as National Standards of Canada by CSA Group. 

----------------------------------------------------------------------------------------------------------- 

CSA B181.0:24 - Definitions, general requirements, and methods of testing for thermoplastic nonpressure piping 

Scope 

1.1 Scope of the B1800 compendium 

This Compendium specifies requirements for compounds and for manufactured pipe and pipe fittings, the relevant test methods, and marking requirements, and applies to thermoplastic nonpressure piping including a) drain, waste, and vent pipe and pipe fittings; b) sewer and storm pipe and pipe fittings; and c) accessories such as factory-assembled expansion joints, closet flanges, backwater valves, and cleanouts. Note: This Compendium does not specify requirements for venting of combustion gases. In Canada, ULC S636 specifies testing and marking requirements for pipe, fittings, and accessories intended for venting of combustion gases. In the U.S., UL 1738 specifies testing and marking requirements for pipe, fittings, and accessories intended for venting of combustion gases. 

1.2 Scope of this Standard 

This Standard specifies definitions, general requirements for compounds and for manufactured pipe and pipe fittings, the relevant test methods, and marking requirements. 

1.3 Intent of this Standard

 This Standard is intended to be used in conjunction with one of the other Standards in the CSA B181 or CSA B182 series to form a complete Standard for a particular product. 

1.4 Terminology

 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non- mandatory) to define their application. 

------------------------------------------------------------------------------------------------------------ 

CSA B181.1:24 - Acrylonitrile-butadiene-styrene (ABS) drain, waste, and vent pipe and pipe fittings 

Scope 

1.1 General 

This Standard specifies requirements for acrylonitrile-butadiene-styrene (ABS) drain, waste, and vent (DWV) pipe, pipe fittings (including push-fit fittings), and accessories such as factory-assembled expansion joints, closet flanges, and backwater valves. Notes: 1) Recommended installation practices for ABS-DWV pipe are specified in Annex A. Use of these recommended practices can help to ensure proper installation and optimum service life. 2) The maximum pressure used to test DWV installations should be 100 kPa (see Clause A.5.2). 3) This Standard does not specify requirements for venting of combustion gases. In Canada, ULC S636 specifies testing and marking requirements for pipe, fittings, and accessories intended for venting of combustion gases. In the U.S., UL 1738 specifies testing and marking requirements for pipe, fittings, and accessories intended for venting of combustion gases. 

------------------------------------------------------------------------------------------------------------ 

CSA B181.2:24 - Polyvinylchloride (PVC) and chlorinated polyvinylchloride (CPVC) drain, waste, and vent pipe and pipe fittings 

Scope 

1.1 General 

This Standard specifies requirements for polyvinylchloride (PVC) and chlorinated polyvinylchloride (CPVC) drain, waste, and vent (DWV) pipe, pipe fittings (including push-fit fittings), and accessories such as factory-assembled expansion joints, closet flanges, backwater valves, and fire-stop fittings*. * The fire stop is for use in fire separations only. It can be subject to code requirements not covered in this Standard. Notes: 1) Recommended installation practices for PVC-DWV pipe are specified in Annex A. Following these practices will help ensure proper installation and optimum service life. 2) The maximum pressure used to test DWV installations should be 100 kPa (see Clause A.5.2). 3) This Standard does not specify requirements for venting of combustion gases. In Canada, ULC S636 specifies testing and marking requirements for pipe, fittings, and accessories intended for venting of combustion gases. In the U.S., UL 1738 specifies testing and marking requirements for pipe, fittings, and accessories intended for venting of combustion gases. 

------------------------------------------------------------------------------------------------------------ 

CSA B181.3:24 - Polyolefin and polyvinylidene fluoride (PVDF) laboratory drainage systems 

Scope 

1.1 General 

This Standard specifies requirements for compounds, pipe, and fittings used in polyolefin and polyvinylidene fluoride (PVDF) laboratory drainage systems for corrosive applications. Notes: 1) Polyolefin includes both PE and PP plastics. 2) PVDF includes emulsion or suspension polymerization of vinylidene fluoride, and copolymers of vinylidene and hexafluoropropylene produced by emulsion or suspension. 3) Other thermoplastics may be certified to this Standard provided they comply with the requirements specified in this Standard. 

1.2 Joining method 

Pipe and fittings covered in this Standard are intended to be joined by heat fusion using joining equipment supplied by the manufacturer. 

1.3 Transitioning between different manufacturers’ products 

This Standard is not intended to provide for interchangeability between plastic pipe and fittings from different manufacturers, but it does allow for transition fittings used to join one manufacturer’s product to another’s provided the joining technique is other than heat fusion. Note: See Annex A for guidance on fusion joints and aboveground and underground installations. 

1.4 Differing or additional characteristics 

Polyolefin laboratory drainage systems having characteristics differing from or additional to those covered by this Standard should be investigated to determine whether they comply with the intent of this Standard. 

------------------------------------------------------------------------------------------------------------ 

CSA B181.5:24 - Coextruded acrylonitrile-butadiene- styrene/polyvinylchloride (ABS/PVC) drain, waste, and vent pipe 

Scope 

1.1 General 

This Standard specifies requirements for coextruded thermoplastic drain, waste, and vent (DWV) pipe with an outer layer of acrylonitrile-butadiene-styrene (ABS) and an inner layer of polyvinylchloride (PVC), or with outer and inner layers of ABS and a core of PVC. 

1.2 Intent of this Standard 

Pipe manufactured in accordance with this Standard is intended to be used with fittings, accessories, and solvent cement that comply with CSA B181.1. Note: Recommended storage, handling, and installation practices for coextruded ABS/PVC-DWV pipe are provided in Annex A of CSA B181.1. Use of these recommended practices can help to ensure proper installation and optimum service life. 

------------------------------------------------------------------------------------------------------------ 

CSA B182.1:24 - Plastic drain and sewer pipe and pipe fittings 

Scope 

1.1 General 

This Standard specifies requirements for a) plastic drain and sewer pipe and plastic pipe fittings with pipe stiffness of 275, 320, or 625 kPa, including single-wall, coextruded, and coextruded dual-wall pipe with a smooth interior; b) single-wall, non-corrugated, perforated plastic pipe and plastic pipe fittings with a pipe stiffness of 200 kPa; c) coextruded dual-wall perforated plastic pipe with a smooth interior, corrugated exterior, and a pipe stiffness of 200 kPa; and d) solvent cement. Notes: 1) Industrial waste disposal lines should be installed only with the approval of the authority having jurisdiction because chemicals not commonly found in drains and sewers, and temperatures greater than 60 ° C, can be encountered. 2) Annex A provides guidance on the relationship between pipe stiffness and the end use of the pipe. 

------------------------------------------------------------------------------------------------------------ 

CSA B182.2:24 - PSM type polyvinylchloride (PVC) sewer pipe and fittings 

Scope 

1.1 General 

This Standard specifies requirements for SDR 26, 28, 35, and 41 PSM type polyvinylchloride (PVC) perforated and non-perforated sewer pipe and fittings. Notes: 1) Industrial waste disposal lines should be installed only with the approval of the authority having jurisdiction because chemicals not commonly found in drains and sewers, and temperatures greater than 60 ° C, can be encountered. 2) Nominal pipe size is indicated by an NPS designation and actual dimensions are given in millimeters. For example, an NPS-10 pipe will be nominally 10 in in diameter. 

1.2 Multilayer construction 

Pipe manufactured to this Standard may have multilayer construction, and the middle layer may have reprocessed-recycled content. Note: In this Standard, the term "multilayer" refers to pipe having three layers. 

------------------------------------------------------------------------------------------------------------ 

CSA B182.4:24 - Profile polyvinylchloride (PVC) sewer pipe and fittings 

Scope 

1.1 General 

This Standard specifies requirements for profile polyvinylchloride (PVC) sewer pipe and fittings of pipe stiffness 70 and 320 (PS70 and PS320), based on controlled inside diameter. Notes: 1) Pipe and fittings manufactured in accordance with this Standard should be installed in accordance with CSA B182.11. 2) Industrial waste disposal lines should be installed only with the approval of the authority having jurisdiction because chemicals not commonly found in drains and sewers, and temperatures greater than 60 ° C, can be encountered. 3) When PS70 pipe is used, the appropriate authority having jurisdiction should be consulted. 

------------------------------------------------------------------------------------------------------------ 

CSA B182.6:24 - Profile polyethylene (PE) sewer pipe and fittings for leak-proof sewer applications 

Scope 

1.1 General 

This Standard specifies requirements for open profile polyethylene (PE) sewer pipe and fittings with annular corrugations for leak-proof applications (e.g., sanitary sewer and other gravity-flow applications). Notes: 1) Pipe and fittings manufactured in accordance with this Standard should be installed in accordance with CSA B182.11. 2) See Annex A for recommended quality control test frequencies. 3) See Annex C for fitting patterns of the lay length of fittings covered by this Standard. 4) Annex D should be followed to ensure the requested products are described adequately. 

------------------------------------------------------------------------------------------------------------ 

CSA B182.8:24 - Profile polyethylene (PE) storm sewer and drainage pipe and fittings 

Scope 

1.1 General 

This Standard specifies requirements for open profile polyethylene (PE) storm sewer and drainage pipe and fittings with annular corrugations for gasketed and non-gasketed leak-proof applications. The products covered under this Standard may be manufactured using either virgin or recycled (post- industrial or post-consumer) materials. Notes: 1) Pipe and fittings manufactured in accordance with this Standard should be installed in accordance with CSA B182.11. 2) See Annex A for recommended quality control test frequencies. 3) See Annex C for fitting patterns of the lay length of fittings covered by this Standard. 4) Annex F should be followed to ensure the requested products are described adequately. 5) See Annex G for additional minimum quality control test frequencies for pipes made with recycled materials. 1.2 Exclusions This Standard does not cover 210 kPa pipe in sizes smaller than NPS-12. 

------------------------------------------------------------------------------------------------------------ 

CSA B182.11:24 - Standard practice for the installation of thermoplastic drain, storm, and sewer pipe and fittings 

Scope 

1.1 General 

This Standard specifies requirements for the installation and testing of thermoplastic and steel- reinforced PE pipes used for the conveyance of drain, storm, and sanitary effluent in gravity-flow systems. Note: Users of this Standard should recognize that installation specifications cover a broad range of conditions for thermoplastic pipe. The engineer should tailor the installation specifications to special conditions and the contract documents. The documentation should specify any work or materials not covered by this Standard. 

1.2 Applicability 

This Standard applies to pipe manufactured in accordance with CSA B182.1, CSA B182.2, CSA B182.4, CSA B182.6, CSA B182.8, CSA B182.12, CSA B182.13, CSA B182.14, and CSA B182.15. 1.3 Exclusions This Standard does not apply to pipe manufactured in accordance with CSA B181.1, CSA B181.2, CSA B181.3, and CSA B181.5. Notes: 1) For the installation practice of pipe manufactured in accordance with CSA B181.1 and CSA B181.5, see Annex A of CSA B181.1. 2) For the installation practice of pipe manufactured in accordance with CSA B181.2, see Annex A of CSA B181.2. 3) For the installation practice of pipe manufactured in accordance with CSA B181.3, consult the manufacturer. 

----------------------------------------------------------------------------------------------------------- 

CSA B182.12:24 - Profile polypropylene (PP) storm sewer pipe and fittings 

Scope 

1.1 General 

This Standard specifies requirements for open profile polypropylene (PP) storm sewer pipe and fittings for leak-proof applications. Profile wall pipe includes only open profile with smooth interior and sizes based on controlled inside diameter. Open profile pipe is of an annular construction. Notes: 1) Pipe and fittings manufactured in accordance with this Standard should be installed in accordance with CSA B182.11. 2) See Annex A for recommended quality control test frequencies. 3) See Annex B for base inside diameters. 4) See Annex C for fitting patterns of the lay length of fittings covered by this Standard. 5) See Annex D for perforation details. 6) Annex E should be followed to ensure the requested products are described adequately. 7) Appropriate structural design criteria for PP storm sewer pipe can be found in Appendix X2 of ASTM F2881/ F2881M. 

------------------------------------------------------------------------------------------------------------ 

CSA B182.13:24 - Profile polypropylene (PP) sewer pipe and fittings for leak-proof sewer applications 

Scope 1.1 General 

This Standard specifies requirements for profile polypropylene (PP) sewer pipe and fittings for leak- proof applications (e.g., sanitary sewer and other gravity-flow applications). Profile wall pipe includes both open and closed profile with smooth interiors and sizes based on controlled inside diameter. Open and closed profile pipe are both of an annular construction but not compatible or interchangeable due to structural differences in profile geometries. Notes: 1) Pipe and fittings manufactured in accordance with this Standard should be installed in accordance with CSA B182.11. 2) See Annex A for recommended quality control test frequencies. 3) See Annex B for base inside diameters. 4) See Annex C for fitting patterns of the lay length of fittings covered by this Standard. 5) Annex D should be followed to ensure the requested products are described adequately. 6) Appropriate structural design criteria for PP sewer pipe can be found in ASTM F2764/F2764M. 

-----------------------------------------------------------------------------------------------------------

CSA B182.14:24 - Profile steel reinforced polyethylene (SRPE) storm sewer pipe and fittings 

Scope 

1.1 General 

This Standard specifies requirements for profile steel reinforced polyethylene (SRPE) sewer pipe and fittings for storm sewer, and other gravity-flow applications. Profile wall pipe in this Standard includes open profile pipe of helical construction, with a smooth interior and sizes based on controlled inside diameter. The pipe can be perforated for specific applications as required. Notes: 1) Pipe and fittings manufactured in accordance with this Standard should be installed in accordance with CSA B182.11. 2) The structural design of this product should be in accordance with the manufacturer’s recommendations. 3) See Annex A for recommended quality control test frequencies. 4) See Annex B for base inside diameters used to determine installation deflection limits. 5) See Annex C for fitting patterns covered by this Standard. 6) See Annex D for examples of Type 3 non-gasketed coupling joints. 7) The ordering recommendations in Annex E should be followed to ensure the requested products are described adequately. 

------------------------------------------------------------------------------------------------------------

CSA B182.15:24 - Profile steel reinforced polyethylene (SRPE) sewer pipe and fittings 

Scope 

1.1 General 

This Standard specifies requirements for profile steel reinforced polyethylene (SRPE) sewer pipe and fittings for sanitary sewer and other gravity-flow applications. Profile wall pipe in this Standard includes open profile pipe of helical construction, with a smooth interior and sizes based on controlled inside diameter. The pipe can be perforated for specific applications as required. Notes: 1) Pipe and fittings manufactured in accordance with this Standard should be installed in accordance with CSA B182.11. 2) The structural design of this product should be in accordance with the manufacturer’s recommendations. 3) See Annex A for recommended quality control test frequencies. 4) See Annex B for base inside diameters used to determine installation deflection limits. 5) See Annex C for fitting patterns covered by this Standard. 6) The ordering recommendations in Annex D should be followed to ensure the requested products are described adequately.

 

Document History

  1. CSA B1800:24

    👀currently
    viewing


    Thermoplastic Nonpressure Piping Compendium

    • Most Recent
  2. CSA B1800:21


    Thermoplastic Nonpressure Piping Compendium

    • Historical Version
  3. CSA B1800-18


    Thermoplastic Nonpressure Piping Compendium, Includes Update No. 1 (2019)

    • Historical Version
  4. CSA B1800-15


    Thermoplastic Nonpressure Piping Compendium, Update No. 1 (2015), Update No. 2 (2015)

    • Historical Version
  5. CSA B1800-11


    Thermoplastic Nonpressure Piping Compendium (Consists of B181.0, B181.1, B181.2, B181.3, B181.5, B182.1, B182.2, B182.4, B182.6, B182.7, B182.8 and B182.11), Includes Update No. 1 (2011), Update No. 2 (2013)

    • Historical Version
  6. CSA B1800-06


    Thermoplastic Nonpressure Piping Compendium (Consists of B181.0, B181.1, B181.2, B181.3, B181.5, B182.1, B182.2, B182.4, B182.6, B182.7, B182.8 and B182.11), Includes Update No. 1 (2007), Update No. 2 (2007), Update No. 3 (2008), Update No. 4 (2009)

    • Historical Version
  7. CAN/CSA B1800-02


    Plastic Nonpressure Pipe Compendium - B1800 Series (Consists of B181.1, B181.2, B181.3, B181.5, B182.1, B182.2, B182.4, B182.6, B182.7, B182.8 and B182.11)

    • Historical Version
  8. CSA B1800-99 No. 2


    Plastic Nonpressure Pipe Compendium- General Instruction No. 2

    • Historical Version
  9. CSA B1800 SERIES-99


    Plastic Nonpressure Pipe Compendium - B1800 Series (Consists of B181.1, B181.2, B181.3, B181.5, B182.1, B182.2, B182.4, B182.6, B182.7 and B182.11)

    • Historical Version
  10. CSA B1800-99


    Plastic Nonpressure Pipe Compendium

    • Historical Version