Language:
    • Available Formats
    • Options
    • Availability
    • Priced From ( in USD )
    • Printed Edition
    • Ships in 1-2 business days
    • $63.00
    • Add to Cart
    • Printed Edition + PDF
    • Immediate download
    • $85.00
    • Add to Cart

Customers Who Bought This Also Bought

 

About This Item

 

Full Description

1.1 These test methods cover the miniature vane test in saturated fine-grained, cohesive clay and silt soils for the estimation of undrained shear strength. Knowledge of the nature of the soil in which each vane test is to be made is necessary for assessment of the applicability and interpretation of the test results. These test methods are not applicable to sandy soils or non-plastic silts, which may allow drainage during the test. These test methods are intended for soils which have an undrained shear strength less than 1.0 tsf [100 kPa].
Note 1: Vane failure conditions in higher strength clay and predominately silty soils may deviate from the assumed cylindrical failure surface, thereby causing error in the measured strength.
1.2 These test methods include the use of both conventional calibrated torque spring units (Method A) and electrical torque transducer units (Method B) with a motorized miniature vane shear device.
1.3 Laboratory vane is an ideal tool to investigate strength anisotropy in the vertical and horizontal directions, if suitable samples (specimens) are available.
1.4 The values stated in either inch-pound units or SI units [presented in brackets] are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Reporting of test results in units other than inch-pound shall not be regarded as nonconformance with this standard.
1.4.1 The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F = ma) calculations are involved.
1.5 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
 

Document History

  1. ASTM D4648/D4648M-24

    👀currently
    viewing


    Standard Test Methods for Laboratory Miniature Vane Shear Test for Saturated Fine-Grained Soil

    • Most Recent
  2. ASTM D4648/D4648M-16


    Standard Test Methods for Laboratory Miniature Vane Shear Test for Saturated<brk/>Fine-Grained Clayey Soil

    • Historical Version
  3. ASTM D4648/D4648M-13


    Standard Test Method for Laboratory Miniature Vane Shear Test for Saturated Fine-Grained Clayey Soil

    • Historical Version
  4. ASTM D4648/D4648M-10


    Standard Test Method for Laboratory Miniature Vane Shear Test for SaturatedFine-Grained Clayey Soil

    • Historical Version
  5. ASTM D4648-05


    Standard Test Method for Laboratory Miniature Vane Shear Test for SaturatedFine-Grained Clayey Soil

    • Historical Version
  6. ASTM D4648-00


    Standard Test Method for Laboratory Miniature Vane Shear Test for Saturated Fine-Grained Clayey Soil

    • Historical Version