Section   Scope 1  Table of Contents 1.11 Referenced Documents 2 Terminology 3  Definitions 3.1  Description of Terms Specific to this Standard 3.2  Abbreviations 3.3 Significance and Use 4 Related Issues and Procedures 5  Continuity with the Weather Barrier Systems 5.1  Joints and Anchorages 5.2  Moisture Entrapment 5.3  Water-Resistive Barrier 5.4  Weatherability 5.5  Construction Sequence 5.6  Construction Damage 5.7  Inspection 5.8  Rough Opening 5.9   Rough Opening Size 5.9.1   Insulating or Filling the Rough Opening Gap 5.9.2  Materials Protection 5.10  Cleaning and Maintenance 5.11  Dissimilar Materials 5.12  Flashing Requirements 5.13  Fastening Systems/Anchorage 5.14  Shimming 5.15  Pan Flashing Systems and Subsills for Weatherability 5.16  Pre-Installation Procedures 5.17  Sealants-Selection and Use 5.18  Window Cleaner Anchors and Related Safety
  Hardware 5.19 Continuity Between the Fenestration Products and
 Other Components of the Building Envelope 6 Water Shedding Strategies of Wall and Roof Systems 7  Concept of Surface Barrier Systems and
  Membrane/Drainage Systems 7.1   Surface Barrier Systems 7.1.1   Membrane/Drainage Systems 7.1.2  Identification of Systems 7.2 Installation Methods For Windows 8  Windows in Walls Utilizing a Membrane/Drainage
  System 8.1   Windows with Perimeter Mounting Flanges
   (Nail Fins) in Drainage Type Wall Construction 8.1.1    Flange Types 8.1.1.1    Selection of Installation Method 8.1.1.2     Method A 8.1.1.3.1     Method B 8.1.1.3.2     Method A1 8.1.1.3.3     Method B1 8.1.1.3.4   Non-Finned Windows in Membrane/Drainage
   Type Walls 8.1.2  Windows in Walls Utilizing a Barrier Wall System
  (Sealant Method) 8.2  Windows in Walls Utilizing an Exterior Barrier System
  (EIFS or Direct Applied) 8.3  Alternative Approved Installation Methods for the
  Installation of Windows 8.4   Extreme Wind/Water Conditions 8.4.1    Membrane Drainage Wood Frame Construction 8.4.1.1    Masonry Construction with Surface Barrier
    Stucco Facade 8.4.1.2  Special Considerations 8.5   Aluminum Framed Windows 8.5.1   Vinyl Framed Windows 8.5.2  Replacement Window Installation 8.6   Partial Window Replacement for Existing Integral
   Flange Windows 8.6.1   Partial Replacement of Mill Shop Wood Windows 8.6.2    "Mill Shop" Wood Windows (Vertical or Horizontal
    Sliding) 8.6.2.1   Complete Window Replacement 8.6.3    Destructive Window Replacement (Fin Type) 8.6.3.1    Non-Destructive Window Replacement
    (Non-Fin Type) 8.6.3.2 Installation Methods for Doors 9  Doors in Walls Utilizing a Membrane/Drainage System 9.1   Doors with Perimeter Mounting Flanges
   (Nailing Fins) in Drainage Type Wall
   Construction 9.1.1    Flange Types 9.1.1.1    Selection of Installation Method 9.1.1.2     Method A 9.1.1.4.1     Method B 9.1.1.4.2     Method A1 9.1.1.4.3     Method B1 9.1.1.4.4   Hinged Swing (Non-finned) Doors in Membrane/
   Drainage Type Walls 9.1.2 Installation Methods for Skylights 10  Product Types 10.1  Flashing Procedures 10.2  Aluminum/Copper Sheet Flashing 10.3  Aluminum/Copper Step Flashing (Fabricated or
  Engineered) 10.4  Membrane Flashing 10.5 Post-Installation Procedures 11 Keywords 12 Air Barrier Foam Sealant Used in the Rough
 Opening Gap Annex A1 Emergency Escape and Rescue Requirements Annex A2 Minimum Height Requirements for Interior Height of
 Pan Flashing Annex A3 Sealants Annex A4 Window/Door Flashing Types Appendix X1 Cautions for Installation Appendix X2 Other Referenced Installation Guides Appendix X3 Alternate Installation Methods Appendix X4 Air Leakage Sealing of Interior Perimeter Rough
 Opening (Air & Water Seal) Appendix X5