Hello. Sign In
Standards Store
Look Inside

IEC 61009-2-1

1st Edition, July 1, 1991

Complete Document

Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO´s) Part 2-1: Applicability of the general rules to RCBO´s functionally independent of line voltage



Detail Summary

Active, Most Current

EN
FR
Additional Comments:
BILINGUAL
Format
Details
Price (USD)
PDF
Single User
$25.00
Print
In Stock
$25.00
Add to Cart

Product Details:


Description / Abstract:

This International Standard applies to residual current operated circuit-breakers with integral overcurrent protection (RCBO’s) functionally independent of line voltage, for household and similar uses incorporating overcurrent protection having rated voltages not exceeding 440 V a.c., rated currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A, for operation at 50 Hz or 60 Hz.

These devices are intended to protect people against indirect contact, the exposed conductive parts of the installation being connected to an appropriate earth electrode and to protect against overcurrents the wiring installations of buildings and similar applications. They may be used to provide protection against fire hazards due to a persistent earth fault current, without the operation of the overcurrent protective device.

RCBOs having a rated residual operating current not exceeding 30 mA are also used as a means for additional protection in the case of failure of the protective means against electric shock.

This standard applies to devices performing simultaneously the function of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value, and also of performing the function of making, carrying and breaking overcurrents under specified conditions.

NOTE 1 The content of the present standard related to the operation under residual current conditions is based on IEC 61008.

The content of the present standard related to protection against overcurrents is based on IEC 60898.

NOTE 2 RCBOs are essentially intended to be operated by uninstructed persons and designed not to require maintenance. They may be submitted for certification purposes.

NOTE 3 Installation and application rules of RCBOs are given in IEC 60364.

RCBOs of the general type are resistant to unwanted tripping, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover.

RCBOs of the S type are considered to be sufficiently proof against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs.

NOTE 4 Surge arresters installed downstream of the general type of RCBOs and connected in common mode may cause unwanted tripping.

NOTE 5 RCBOs within the scope of the present standard are considered as suitable for isolation (see 8.1.3)

Special precautions (e.g. lightning arresters) may be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines) (see IEC 60364-4-443).

NOTE 6 For RCBOs having a degree of protection higher than IP20 special constructions may be required.

This standard also applies to RCBOs obtained by the assembly of an adaptable residual current device with a circuit-breaker. The mechanical assembly shall be effected in the factory by the manufacturer, or on site, in which case the requirements of annex G shall apply. It also applies to RCBOs having more than one rated current, provided that the means for changing from one discrete rating to another is not accessible in normal service and that the rating cannot be changed without the use of a tool.

Supplementary requirements may be necessary for RCBOs of the plug-in type.

Particular requirements are necessary for RCBOs incorporated in or intended only for association with plugs and socket-outlets or with appliance couplers for household and similar general purposes.

NOTE 7 For the time being, for RCBOs incorporated in, or intended only for plugs and socket-outlets, the requirements of this standard in conjunction with the requirements of IEC 600884-1 may be used, as far as applicable.

This standard does not apply to:

– RCBOs intended to protect motors,

– RCBOs the current setting of which is adjustable by means accessible to the user in normal service.

The requirements of this standard apply for normal environmental conditions (see 7.1). Additional requirements may be necessary for RCBOs used in locations having severe environmental conditions.

RCBOs including batteries are not covered by this standard.

A guide for the co-ordination of RCBOs with fuses is given in annex F.